Videx VX2200 Guida alla Risoluzione dei Problemi Scaricare il pdf (Pagina 49)

PAGE 49 of 68 VX2200 TECHNICAL MANUAL VER1.5

TROUBLE SHOOTING GUIDE

PROBLEM FOUND

POSSIBLE CAUSE POSSIBLE SOLUTION

The system has power but the front panel does

not turn on.

1. Interruption or short circuit of the 13Vdc

output on PSU to the outdoor station;

2. PSU defective or fuse blown.

1. Check the GND and +13V connections

on PSU and on panel, then check the

protection fuse on the output of PSU and

change it if necessary;

2. Check PSU output with and without load.

Front panel display shows “ERROR” and the

unit makes acoustic intermittent signals at

intervals of approx. 2 seconds.

1. Probable short circuit on the BUS “─”and

“L” line;

2. Reversion of polarity on the BUS

connection of a phone, videophone or

accessory;

3. Panel programmed as “Slave” when it

should be as “Master”.

1. Check the BUS connections.

2. Check the polarity of the devices

connected.

3. Configure the device as ”Master”

The system, at the moment of the call, is not

able to let the extension ring, the front panel

makes acoustic signals of line engaged and the

display shows “Error”.

1. The phone or videophone called is not

correctly connected;

2. The cable size (BUS) is to small;

3. The address programmed on the dip-

switch (of the phone, videophone or

accessory) does not correspond to that

called;

4. The concierge (if present in the system)

has been left in programming mode.

1. Check the connection of the BUS

2. Double or increase cable size;

3. Check that the address associated to the

call corresponds to that programmed on

the dip-switch of the phone (videophone

or accessory);

4. Remove concierge from programming

mode.

The outdoor station makes the call correctly,

but when the user answers, the communication

is cut off.

The cable size is too small.

Double or increase cable size

During the conversation, when the door is

opened, the communication is cut off.

The cable size is too small.

Double or increase cable size

The calls goes through, but the conversation is

one-way only.

The supplying voltage on the outdoor station is

too low (under 10.5V).

Increase the supply cable size (GND & 13V).

Check voltage output on PSU and adjust if

necessary.

The audio level of conversation is too low. The levels of the conversation volumes in both

directions are not appropriately adjusted or

balanced.

Adjust on the outdoor station trimmers for

microphone and loudspeaker so as to have the

best levels without oscillations (Larsen effect)

The audio level is at its limit or oscillates

(Larsen effect).

The “Balance” trimmer (outdoor station) is not

appropriately set and/or the conversation

volumes are programmed to high.

Adjust on the outdoor station the “balance”

trimmer until the problem is solved and/or

lower the volumes of the microphone and

loudspeaker.

The door release is not working. 1. Lock defective;

2. Connection wrong or interrupted;

3. Cable size to small;

4. Lock PSU faulty.

1. Change the lock;

2. Check connection continuity;

3. Increase cable size;

4. Check power supply output;

The local floor call does not work. 1. Call push button defective;

2. Connection wrong or interrupted.

1. Check defect;

2. Check connection.

The internal video stations do not turn on. 1. Art.893N power supply defective or in

protection;

2. Art.893N is not operated by the outdoor

station during the call (SL terminal);

3. Connection wrong or interrupted.

1. Check 893 with and without a load;

2. “-C” terminal of art.893N not correctly

connected to the “SL” terminal of the

outdoor station;

3. Check the continuity of the connection

between the monitor supplying wires and

the videophones interested.

The internal video stations turn on, but the

image does not appear.

1. Art.830NC video camera not supplied or

defective;

2. Connection of the V1-V2 signals

interrupted or wrong.

3. Video dip-switches on monitor or

jumpers on camera incorrectly positioned

1. Check and/or change art 830NC;

2. Check connection continuity.

3. Check all dip-switches and jumpers.

The internal video station turns on but the

quality of the image is bad or reflected.

1. Signal V1 or V2 not connected or in short

circuit;

2. V1 & V2 signals inverted;

3. Closing resistances are missing at the end

of the BUS video.

4. Dip-switches or jumpers on monitor or

camera not correctly positioned

1. Check the continuity of the connection

and the isolation to the ground;

2. Check and in case invert the connections;

3. Check and in case apply the closing

resistances on the BUS video.

4. Check dip-switches and jumpers.

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 ... 67 68

Commenti su questo manuale

Nessun commento

Videx VX2200 Guida alla Risoluzione dei Problemi Pagina 49

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di interfono Videx VX2200